• Facebook
  • Instagram
  • Pinterest
  • Email
  • Print
Print Friendly, PDF & Email
  • PDF
  • Facebook
  • Instagram
  • Pinterest
  • Email
  • Print

It’s time for a spot of tea. Did you know to properly brew a pot o’ tea, you should first warm the teapot by swooshing a bit of boiling water inside it. Then, pour the hot water into your teacups to warm them. Add teabags for your preferred strength (from two to four for a standard four-cup pot). Fill the pot with boiling water, stir, and let the tea steep for about 4-5 minutes. It’s during this steeping time when you can run into trouble with the tea cooling too fast. So, pop on a cozy to keep things toasty while the tea is steeping. It will also help keep your tea warm between cups. We offer free pattern downloads for the cozy itself as well as the cute teapot appliqué.

Our design uses standard cotton for the exterior and lining with a layer of insulating fleece in between.

Straight line quilting across both the front and back is functional and adds to the pretty textured look. If you are new to this technique, you may want to check out our Guest Tutorial by Heather Jones on Straight Line Quilting techniques.

Because you only need small ¼ and ½ yard fabric cuts, this is a great ScrapBusters project.

Rick rack accents on both sides are a sweet addition, and that cute little front pocket can hold teabags or accessories.

Our teapot cozy is sized to fit a standard china teapot, as shown in the photos above and below.

If your teapot is similar in size, chances are very good this teapot cozy will fit. The key dimensions to check are indicated by the colored arrows in the drawing below.

If you want to change the size, we suggest printing our pattern and adjusting smaller or larger, using it as your template. Make a paper prototype to test on your teapot. Both the dimensions as well as the curves along the top and bottom are important in order to allow the cozy to fit properly over the girth of a traditional teapot. A simple half circle won’t give you the appropriate coverage. Remember to account for a ½” seam allowance around the curve, but not along the bottom as it is bound. We added 4″ to the overall height and 4½” to the overall width. Click on the drawing below to see a larger view and to better read the color key for the four important dimensions.

Sewing Tools You Need

Fabric and Other Supplies

NOTE: Our design uses FOUR different fabric cuts: two coordinating prints and a solid for the cozy itself plus one additional tiny piece for the teapot appliqué. We dove into our scrap stash for our selections, pulling out the following:

  1. Medium Dots on Aqua from the Cotton Dots collection by Riley Blake Designs (originally used for our Decorative Stitch Pillow Power project)
  2. Daisy in Blue from the Hello Sunshine collection by Riley Blake Designs (originally used for our Everything Apron)
  3. Cotton Couture in Azure by Michael Miller Fabrics (originally used for our Quilted Bed Runner project)
  4. Floral Vintage in Cream from the Vintage Modern collection by Bonnie & Camille for Moda Fabrics (originally used for several projects, including our Patchwork Placemats)
  • ¼ yard of 44″+ wide cotton print fabric for the center panel and front pocket; we used Aqua Dots
  • ½ yard of 44″+ wide cotton print fabric for the outer panels and top loop; we used Blue Daisy
  • ½ yard of 44″+ wide cotton print fabric for the lining and binding; we used Azure Cotton Couture
  • Scrap with a coordinating feature motif – you need an approximate 5″ high x 7″ wide scrap from which to fussy cut the approximate 3″ high x 5″ wide teapot appliqué; we used Cream Floral Vintage
  • ½ yard of insulating fleece: we used Insul-Bright by The Warm Company
  • Scrap of paper backed adhesive for the appliqué – as above, you need an approximate 5″ high x 7″ wide scrap from which to cut the approximate 3″ high x 5″ wide teapot appliqué; we used Wonder Under by Pellon
  • Scrap (an approximate 9″ x 9″ square) of lightweight interfacing for pocket panel; we used 950F ShirTailor by Pellon
  • 1½ yards of coordinating jumbo rick rack; we used jumbo white rick rack
  • All purpose thread to match fabric
  • Decorative thread in a slightly contrasting shade for the appliquéwe used 40 wt rayon in light blue
  • See-through ruler
  • Fabric pen or pencil
  • Seam gauge
  • Seam ripper
  • Scissors or rotary cutter and mat
  • Iron and ironing board
  • Straight pins
  • Hand sewing needle

Getting Started and Pattern Downloads

  1. Download and print the TWO pattern pieces and the ONE template. Print ONE copy of the Tea Cozy Pocket pattern. Print TWO copies of the Tea Cozy pattern. Print ONE copy of the Teapot Appliqué template.
    IMPORTANT: Each pattern/template is ONE 8½” x 11″ sheet. You must print all three PDF files at 100%. DO NOT SCALE to fit the page. There is a guide line on each page to confirm your printout is the correct size. 
  2. Cut out the pattern pieces along the solid lines. Set the teapot template aside; do not cut it out quite yet.
  3. The cozy itself is two pieces. Keep one piece right side up; flip the other piece so it is wrong side up. Butt together the two pieces, following the arrows on the print out, to create the full pattern. Do NOT overlap. Tape in place. Set the assembled pattern aside.
  4. From the fabric for the center panel and front pocket (Aqua Dots in our sample), fussy cut the following:
    TWO 7″ wide x 13″ high rectangles, centering a vertical motif – we used a line of dots
    Using the pocket pattern, cut ONE pocket
    NOTE: We recommend fussy cutting the pocket so it is a perfect match to the center panel. Or at the least, carefully centering the pocket cut. An easy way to do this is to fold the pattern piece in half to position the pocket along a vertical motif.
  5. From the fabric for the outer panels and top loop (Blue Daisy in our sample), cut the following:
    FOUR 6″ wide x 13″ high rectangles
    ONE 1¼” x 5″ strip
  6. From the fabric for the lining and binding (Azure Cotton Couture in our sample), cut the following:
    TWO 2″ x 29″ strips
    Using the assembled tea cozy pattern, cut TWO pieces
  7. From the insulating fleece, cut TWO 17″ x 13″ rectangles.
  8. From the lightweight interfacing, use the pocket pattern to cut ONE piece.
  9. Cut the rick rack into FOUR 13″ lengths.

At Your Sewing Machine & Ironing Board

Preparing the front and back panels

  1. To insure perfect sizing and straight quilting, the teapot cozy pattern will be cut from a pre-assembled and pre-quilted front and back panel.
  2. Find the six main panels and the four lengths of rick rack.
  3. Arrange the panels into two sets of three, each with two outer panels and one center panel.
  4. Place a length of rick rack along each 13″ side of each center panel. The “waves” of the jumbo rick rack should be flush with the raw edge of the fabric. Pin in place.
    NOTE: If you do not use jumbo rick rack, you will need to adjust the position of the trim for the best reveal.
  5. Using an approximate ¼” seam allowance (could be anything less than ½”). Machine baste the rick rack in place.
  6. Place each outer panel, right sides together, on either side of the center panel, sandwiching the rick rack between the layers. Pin in place.
  7. Using a ½” seam allowance, stitch the two center panel seams.
  8. Press flat, pressing the seam allowances and the rick rack toward the outer panels.
  9. You should now have TWO identical 17″ wide x 13″ high panels.
  10. Find the 17″ x 13″ insulating fleece panels. Place them right side up and flat on your work surface.
  11. Place a fabric panel right side up on top of each fleece panel. The edges of both layers should be flush all around. Pin the layers together.
  12. Using your ruler and a fabric pen or pencil, find the exact center of the middle panel. If you fussy cut your panel as recommended above, you should have a vertical motif to help you find the exact center line.
  13. Draw in a vertical center line.
  14. If possible, attach your Walking/Even Feed foot, or engage your machine’s built-in fabric feeding system. Straight-line quilt (sometimes called channel quilting) through the two layers at 1″ intervals, using a quilting bar to set an even distance.
    NOTE: If you do not have a Walking foot and/or a Quilting bar, pre-draw guide lines to follow at 1″ intervals to the left and to the right of the center line with a fabric pen or pencil. Remember, you are working on the right side of the fabric; be sure your marking tool is one that will easily wipe away or will vanish with exposure to the air or the heat of an iron. 
  15. Your quilting is done at 1″ intervals all the way across both the front and back panels.
    NOTE: As mentioned above, you may want to check out our Guest Tutorial by Heather Jones on Straight Line Quilting techniques
  16. Find the tea cozy pattern.
  17. Place it on a quilted panel, carefully lining up the center of the pattern with the center vertical quilting line. Pin the pattern in place on the panel.
  18. Cut out the cozy pattern.
  19. Repeat to cut out a second cozy pattern from the remaining panel.

Pocket and appliqué

  1. Find the fabric pocket panel and the pocket interfacing. Following manufacturer’s instructions, fuse the interfacing to the wrong side of the fabric.
  2. Fold the fabric in half, right sides together, and press to set a center crease. Unfold the fabric, right side up, so the crease line is visible. Set the pocket panel aside.
  3. Find the appliqué fabric. Following manufacturer’s instructions, fuse the paper backed appliqué adhesive to the wrong side of the accent fabric. Use a large enough piece to cover the size of the appliqué template, and position it behind where you plan to cut the appliqué.
  4. Find the teapot appliqué template. For the more detailed shapes of appliqués, we recommend cutting “wild” around the pattern first rather than cutting along the solid line. Carefully position the trimmed template on the fabric; you want the fabric’s motif to be straight within the template and nicely centered. Pin the trimmed template to the accent fabric.
  5. Cut out the teapot appliqué along the solid line.
  6. Remove the paper backing from the appliqué shape.
  7. Find pocket panel. It should be right side up and flat so the crease line is visible.
  8. Place the appliqué on the bottom half of the pocket rectangle. The appliqué should be centered side-to-side and top-to-bottom.
  9. Fuse the appliqué in place, following manufacturer’s instructions.
  10. Thread the machine with bobbin thread in the bobbin and decorative thread in the top (we used light blue). Attach a decorative stitch presser foot or appliqué presser foot. We used the clear Janome Satin Stitch foot with its wide front and helpful center guide notch.
  11. Select a small zig zag stitch. Practice first on scraps to get the stitch length and width that works/looks best for you.
  12. Zig zag around all the edges of the teapot appliqué, using the raw edge of the fabric as the center guide for your zig zag stitch. Go slowly and don’t be afraid to stop, with the needle in the down position, and re-adjust along the way in order to keep your stitching smooth and pretty. This teapot is a more advanced appliqué shape; the curves of the handle and the top will definitely require a bit of adjustment along the way.

    NOTE: If you are new to this technique, check out our Appliqué Tutorial
  13. Fold the pocket in half, right sides together, along the original crease line. Pin along both sides. The bottom should be left open.
  14. Using a ½” seam allowance stitch both short side seams.
  15. Clip the corners and press open the seam allowances.
  16. Turn the pocket right side out through the bottom opening. Using a long, blunt end tool, gently push out the upper corners so they are nice and sharp. A chopstick, knitting needle or point turn are all good tool options. Press the pocket flat.
  17. Find whichever tea cozy cut-out you want to be the front panel. Place it right side up and flat on your work surface. Place the finished pocket right side up at the bottom of the center panel. The bottom raw edges of the pocket should be flush with the bottom raw edges of the cozy. The pocket should be centered side-to-side within the center panel. Pin the pocket in place along both sides. Again, if you fussy cut the pocket as recommended, the motif of the pocket should align nicely with the motif of the center panel.
  18. If necessary, re-thread the machine with thread to match the main fabric in the top and bobbin.
  19. Edgestitch the pocket in place along both sides.

Make loop and sew front to back

  1. Find the 1¼” x 5″ strip. Fold it in half lengthwise, wrong sides together, and press to set a center crease. Unfold, wrong side up, so the crease line is visible. Fold in each 5″ raw edge to the center crease line.
  2. Press in half again along the original crease line. Edgestitch the length of the strip through all the layers.
  3. Fold the strip in half, aligning the raw ends, to form a loop. Place the loop at the top center of the front cozy panel, aligning the raw ends of the loop with the raw edge of the cozy panel. Machine or hand baste in place.
  4. Place the cozy front panel right side up and flat on your work surface.
  5. Place the cozy back panel right side down so the two layers are right sides together. Pin together along the curve. The bottom remains open.
  6. Using a ½” seam allowance, stitch along the curve.
  7. Clip the curves, then grade the seam, trimming back one side of the seam allowance to ¼”. This allows the seam to fold in nicely and helps reduce bulk.

Lining and binding

  1. Find the two lining panels. Place them right sides together and pin in place along the curve. The bottom remains open.
  2. Using a ½” seam allowance, stitch along the curve.
  3. Press the seam allowance open and clip the curve as above.
  4. Keep the lining wrong side out. Find the exterior cozy, which should be right side out. Slip the lining inside the exterior so the two layers are now wrong sides together. Align the center curved seams of both layers.
  5. Unlike a lined bag where the force of gravity helps keep the lining in place, the lining of this teapot cozy will want to drop out when you lift the cozy off the teapot. To help hold it in place, thread a hand sewing needle with thread to best match the exterior fabric and hand tack the lining to the exterior cozy at about five points along the seam. Your stitches should be hidden within the seam itself. Knot off each hand tack on the inside.
  6. Find the two 2″ strips of binding. Stitch the strips together end to end, using a ¼” seam allowance, to create one continuous strip.
  7. Create the folded binding with your favorite method. You can use a manual bias tape maker or you can make binding by hand, following the same method you used to create the binding loop above: fold the strip in half, wrong sides together, to create a center crease. Unfold, then fold each side in to meet together at the center crease. Then re-fold again along the original crease line.
  8. Starting at the center back of the cozy, slip the finished binding over the bottom raw edges and pin in place. Overlap or seam the binding where the ends meet at the center back.
  9. If necessary, re-thread the machine with thread to match the binding fabric in the top and bobbin.
  10. Edgestitch in place through all the layers around the entire bottom opening. Go slowly to insure you catch both the front and back of the binding in this one seams.
    NOTE: We have summarized the binding steps here because there are a number of options, and everyone has their favorite way to attach and join their binding. The number one rule is ‘slow and steady wins the race.’ You’re sewing around a bit of a curve, which is trickier than a straight line, and are binding several layers. Don’t fear the pin! Use plenty, removing them as you go. If you are brand new to the technique, take a look at our tutorial: A Complete Step-by-Step For Binding Quilts & Throws. We show detailed instructions for a number of attaching and finishing options. 


Project Design: Alicia Thommas
Sample Creation: Debbie Guild

Notify of

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business. When commenting, your name will display but your email will not.

Oldest Most Voted
Inline Feedbacks
View all comments
10 months ago

Thank you so much for the wonderful cozy pattern. I have been a tea drinker since I was in grade school. Have been looking for a pattern for a while now. Now to find some material.

Liz Johnson
Liz Johnson
10 months ago
Reply to  JoAnn

Thanks, JoAnn – I think you’ll have lots of fun with this project. Let us know how yours turns out. If you follow-up on any of the social media channels, we love it if you shared a pic or two.

11 months ago
I am wondering what the width of your jumbo might be.  I have wrights 
jumbo rick rack and it is way too narrow to make this look like yours.  
There are multiple widths of jumbo rick rack I have discovered.  Thanks, 
Liz Johnson
Liz Johnson
11 months ago
Reply to  Judy

Hi Judy – Yes, packaged rick rack options usually top out at about 5/8″ — but you can find widths at 1″ to 1-1/2″ online and sometimes on by-the-yard reels at fabric stores. We used a 1″ – but you can certainly substitute whatever you’d like.

11 months ago
Reply to  Liz Johnson

Thank you so much. I love your work and your tutorials. I have followed you for years. Loved the quick response.

Liz Johnson
Liz Johnson
11 months ago
Reply to  Judy

Thank you, Judy – we’re lucky to have you as such a lovely follower.

Eileen Emerson
Eileen Emerson
1 year ago

Thanks for this lovely pattern. I’ll be sewing one of these for myself shortly. Happy St Patrick’s Day.

Liz Johnson
Liz Johnson
1 year ago
Reply to  Eileen Emerson

You’re welcome, Eileen. We hope you have fun with the project! Happy St Paddy’s to you as well.

Caroline from France
Caroline from France
3 years ago

I am going to use this pattern for a teapot cozy for my sister who lives in a different country, so I cannot test for size.
Her teapot measures 6.3 inches high; 10.2 inches wide; horizontal surround is 23.6 inches and vertical surround is 20 inches. Looking at it, I think I can use your measurements – could you possibly confirm? I’d be so grateful.

Liz Johnson
Liz Johnson
3 years ago

Hi Caroline – Without actually trying it, we can’t give you a guarantee. You measurements are quite close and all are slightly smaller rather than larger – so that’s always good. The one that is the farthest off seems to be the vertical surround – so her pot is probably not quite as chubby 🙂 So it might be a bit loose. Unfortunately, we can’t adjust our patterns for every request, but in general – it sounds like it will be a pretty good fit for your sister’s teapot.

3 years ago

Is there a video? I’m a visual learner. I’d love to make this!

Liz Johnson
Liz Johnson
3 years ago
Reply to  Ana

@Ana – So sorry, we don’t do video tutorials. However, our photos and instructional steps are very thorough. We hope you’ll give it a go.

5 years ago

Oh, yum!  I am a dedicated

Oh, yum!  I am a dedicated morning tea drinker and I have a collection of tea pots, but no cozy!  Then here you come, doing one up in my favorite color!  You’re so thoughtful!  Thank you!  

Translate »

You cannot copy content of this page



Enter your email address below to subscribe to the Sew4Home newsletter. Be the first to see new projects and patterns, helpful techniques, and new resources to enhance your sewing experience.


We will never sell, rent or trade your personal information to third parties.