Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest Instagram


Clipping and Stitching Corners Correctly

Printer-friendly versionPDF version

One of the common areas of sewing frustration, especially if you're new, is the corner. Those pesky four corners create any square or rectangular item, like the home décor standard: the pillow! In reality, any time you sew two pieces together then turn them right side out, that turned-out seam becomes the clean, finished edge you (and everyone else) will see. The number one goal when sewing a corner is to be precise. You must stop and pivot at the exact point where the seam allowances on the two sides intersect. This precision stitching, when combined with proper trimming of the excess fabric from the seam allowance, will create a beautiful sharp point and smooth edge every time.

Sounds simple, right? Mostly it is, but there are some techniques about clipping and stitching corners that will help you maintain the best, cleanest shape every time. From curtain panels to pillow edges to accessory details, by following a few simple steps, you'll never be backed into a corner again!

Everyone's favorite corner is the right or 90˚ angle. You'll find them on pillows, panels, placemats... as well as other items that don't necessarily start with a "P"! These corners come in TWO types: inward and outward. The two are sewn in a similar fashion, but clipped differently.

Although most corners in home décor projects are of the right angle variety, others can be more like a point (or acute angle, which means less than 90°). We used these in our Gypsy Romance 3-D Triangle Pillows.

Then there are the obtuse angles, which means more than 180°. We encountered these on the flap of our Fabric Wallet with Zippered Coin Purse.

And you thought you'd never use geometry when you got older!

For pillows, you can adapt the instructions to create a tapered corner that can actually result in more of a square finish. We have a full tutorial on this specialty corner: Quick Tip: How Tapered Corners Make Square Pillows.  

When you venture into garment sewing, you're likely to see a lot of stitching and clipping of corners on collars and cuffs. The good news is, you'll be ahead of the learning curve thanks to this tutorial.

Our Velvet Border Portfolio Clutch shows a crisp flap for a nice pro finish.

In our examples below, we used a bold red thread so you could see and understand the technique. In actual application, you would select a thread to coordinate with your fabric. In the majority of our photos, we also used our Janome Open Toe Satin Stitch foot so you could clearly see all the stitching. For the majority of corner stitching, a standard pressure foot is the best choice.

Sewing and trimming an OUTWARD right angle corner

  1. When starting out, regardless of the angle, it's a good idea to mark the seam allowance a couple inches from the corner along both sides on the wrong side of your fabric. This will enable you to clearly see where the lines intersect and improve your stitching accuracy. For right angles, it's fairly easy to determine where the two seam allowances intersect by measuring from each corner.
  2. Using your seam allowance measurement (our standard home décor allowance is ½"), measure in from each corner edge with a ruler or seam gauge. About 3-4" should be enough.
  3. With a fabric marking pen or pencil, mark the pivot point on each corner.
    Click to Enlarge
  4. With your fabric right sides together, begin to sew along the seam allowance. As you approach the corner (and your drawn lines), get ready to stop and pivot at the marked point.
    Click to Enlarge
  5. Stop with the needle in the down position. Lift up your presser foot, pivot, lower the foot back into position, and continue sewing.
    Click to Enlarge
  6. With a pair of small, sharp scissors, trim the seam allowance at the point.
  7. First, trim off the corner point at a diagonal, being very careful not to clip your stitches.
    Click to Enlarge
    NOTE: If you do accidentally clip into your seam, don't just leave it! There will be a hole at the corner and the weakened seam could continue to open up. Take the time to re-stitch the seam! This means you will not have much, if any, seam allowance to work with, so you'll need to sew carefully. Stay as close to where you clipped as possible without comprising the shape of your overall project.
  8. After you trim off the point, trim along each side at an angle from the point. This will ensure a sharp corner.
    Click to Enlarge
  9. Turn the piece right side out to see how your point looks. Not so good? That's because you need to gently push out the corner with a point tool. There are a number of different ones you can use, we've pictured an "official" point turner in our photo, but you can also use a simple chopstick or a long, blunt-end knitting needle.
    Click to Enlarge
  10. If you were a little shy about your clipping, you'll feel the extra fabric bunched up in the corner; it kind of feels like a little knot. That means you need to go back in and trim a little more.
  11. Press your project from the right side and admire your sharp little corner.

Sewing an INWARD right angle corner

  1. Mark your corner points in the same manner as above.
    Click to Enlarge
  2. Sew as before, pivoting at the marked corner point intersection.
    Click to Enlarge
  3. This time, instead of cutting off the point, you need to clip into the point. Again, be careful to not cut through your seam.
    Click to Enlarge
  4. Turn your project right side out and see how the corner looks. As above, if needed, turn it inside out again and trim away more seam allowance at the corner.
  5. You'll notice you can see one of our red stitches from the right side. You will be stitching with matching thread, so no worries if a thread peeks thtrough.
    Click to Enlarge

A stitch length option

  1. Sometimes, depending on the fabric type or weight, you may need to adjust your stitch length at each corner. In fact, some sewing experts recommend doing this at any corner in your sewing.
  2. When approaching your corner, shorten your stitch length for a distance equal to your seam allowance. Do this both coming into and going out of the corner. In our sample, this meant we shortened the stitch length ½" before and after the corner pivot point.
  3. This helps insure a sharp point and helps strengthen the corner.
    Click to Enlarge

Added layers

  1. When you have an added layer in a corner, like batting, everything is sewn in the same manner as we've been discussing.
    Click to Enlarge
  2. When you're done stitching, first trim the excess batting to approximately ⅛" from the stitching line. This reduces the bulk. Next, go back and clip the corner fabric layers as described above.
  3. It's often a good idea to trim back the batting around the entire project, rather than just at the corners, especially if you plan to use a line of topstitching along the seamed edge on the right side. For more detail, take a look at our article on Grading Seams
    Click to Enlarge

Different weight fabrics

  1. To fully educate you on all we know about corners, we have to mention an option for dealing with various weights of fabrics. As above with the batting, the idea is to eliminate excess bulk in the corner that prevents you from effectively turning out each point. Believe it or not, sometimes the best way to create a point is to not sew one to begin with!
  2. Mark your seam allowance as shown above, but instead of pivoting at the intersection of the two seam allowances, sew ACROSS the pivot point. The general rules are: on lightweight fabrics (see our example below), sew one stitch across, on medium weight fabrics sew two stitches across, and on heavier weight fabrics sew three stitches.
  3. You would think you'd lose the point, but you'll actually get a good looking one.
    Click to Enlarge

Acute and obtuse points

  1. Acute and obtuse angled points are sewn exactly the same way as the right angles; they just look a little different.
  2. Mark your seam allowance and intersecting or pivot point. On the left is our marked acute angle; on the right is a marked obtuse angle.
    Click to Enlarge
  3. Sew as normal, stopping to pivot at your marked point. You're starting to get the hang of this now!
    NOTE: When you are sewing acute angles, we recommend considering the "cross stitch" method described above. Because the acute point is so narrow, sewing across the pivot point with a stitch or two can be quite helpful. In addition, extra care and a slower speed is recommended because the raw edge can be stretchy (the exception to this would be if you are working with an interfaced piece like the point of a collar).
    Click to Enlarge
  4. Trim the point and seam allowances. The acute angle trims in the same manner as an outward right angle.
    Click to Enlarge
  5. The obtuse angle should be trimmed as more of a simple slope from the point down either side.
    Click to Enlarge
  6. Obtuse angles turn right side out the easiest of all the angles, which makes sense because there's more room at the point.
  7. Acute angle points sometimes need a little more coaxing. You can use a point turning tool as we recommended above, but you may find the very tip of the point still doesn't want to turn. To fix that, all you need is a trusty straight pin. Insert the straight pin into the tip of seam from the right side and gently pull/pick out the point into shape.
    Click to Enlarge


Sample Creation and Instructional Outline: Jodi Kelly


Comments (14)

Melanie Possien said:
Melanie Possien's picture

This is an excellent tutorial-- easy to follow and great for beginners, like me! Thank you! I look forward to seeing what else you have. :)

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Melanie - That's great news - thanks for taking the time to let us know we helped you out with a new skill. And yes! Browse around - there's lots to see and do 

Ruth 47 said:
Ruth 47's picture

Hello, thankyou for  creating this helpful page - I am still having a problem though with sewing insward right angle corners. I find when I turn them the right way round there is a lot of puckering around the corner, like the fabric is under tension. Do you have any advice?

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Ruth - So glad you've found our tutorial helpful. We really did pack all our "pearls of wisdom" into the information above. There are a lot of variables too - especially regarding the fabric you're working with. You might check the notes above about stitch length – shortening your stitch as you come into and go out of the corner. And, try being a bit more aggressive with your clipping (but as always, careful not to clip into the seam), actually clipping small wedges out of the seam allowance - as you might do when clipping a curve. Hope that helps a bit more. 

ruth 47 said:
ruth 47's picture

Many thanks for the quick reply, I'm looking forward to trying your tips tonight :)

Robby Cook said:
Robby Cook's picture

Thank you very much for these clear, concise instructions.  I've been really impressed by Sew4Home's helpful instructions and patterns for many years but have never taken the time to say "thank you".  Your weekly update email is one of my favourites.  

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Robby - Thank you for such a lovely compliment. We're lucky to have you as a follower!

Diane H said:
Diane H's picture

Thank you.  Wish I had read this a loooong time ago.  Extremely helpful advise.

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Diane - You are so welcome. Sometimes it's the easiest things that can be the biggest help.

Caroline from France said:
Caroline from France's picture

Good stuff, thank you. The tip of adjusting the stitch length on approaching a corner is a new one for me; it sounds extremely sensible and I shall adopt it on my next project!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Caroline - Thank you! It's always nice to polish up basic skills!

Annie Dee said:
Annie Dee's picture

Thank you.  Good info to reread.  Going to put this to use right now!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Annie - You are so welcome. Sharp corners here you come!!