• Facebook
  • Instagram
  • Pinterest
  • Email
  • Print
Print Friendly, PDF & Email
  • PDF
  • Facebook
  • Instagram
  • Pinterest
  • Email
  • Print

Although it may seem as if our varied electronic devices operate by magic, we know sooner or later they require a cord to sync, transfer or re-charge. All those little cords can become a tangled mess, making it hard to find what you need when you need it. Keep your cords tidy with these quick and easy wraps. We offer two sizes: one small version for things like tiny ear buds, another for larger items, like power cords. They take just teensy scraps of fabric. We worked with pre-cuts, using a charm square for the small size and a layer cake square for the large size. Great for travel!

A small rectangle of Velcro® allows either size quite of bit of flexibility. Cinch just a single item tightly or loosen to bundle several within one wrap.

How wonderful would this project be as a gift idea? You could even offer to organize someone’s cord drawer with labeled wraps.

We recommend using the same fabric for both sides of the wrap for the most efficient cutting and a seamless finish. That said, it could also be cute to use coordinating prints on the front and back or one print with a matching solid.

Find the pattern link below in the Getting Started section. Then set up your assembly line to whip out your wraps.

This project is a great way to use up a few of your special scraps or the leftover pieces from a pre-cut bundle.

Our small wrap finishes at approximately 4½” x 1½” when open and flat. The large wrap is approximately 6” x 2½” when open and flat. Each wrap is adjustable with the Velcro®.

Sewing Tools You Need

Fabric and Other Supplies

  • Scrap of quilting weight weight cotton for the exterior layers (front and back); you need an approximate 5” x 5” square for the small wrap and an approximate 10” x 10” square for the larger wrap; we used a charm square and a layer cake square
  • Scrap of lightweight fusible interfacing – same approximate sizes as above; we used Pellon Shape Flex which adds body but is still very flexible
  • Scrap of ¾” Velcro® for the small wrap, 1” for the large wrap – you only need about an inch for each (1” for small, 1½” for large)
  • All-purpose thread to match fabric
  • See-through ruler
  • Fabric pen or pencil
  • Seam gauge
  • Seam ripper
  • Scissors or rotary cutter and mat
  • Iron and ironing board
  • Straight pins

Getting Started and Pattern Download

  1. Download and print the pattern.
    IMPORTANT: This PDF contains ONE 8 ½” x 11” sheet containing patterns for both sizes of cord wraps. You must print the PDF file at 100%. DO NOT SCALE to fit the page. The pattern is designed to print horizontally (landscape rather than portrait). There is a  guide rule on each page to confirm your print out is to size.
  2. Cut out the pattern pieces along the solid lines.
  3. From the appropriately sized width of Velcro®, cut ONE 1” length for each small wrap and ONE 1½” length for each large wrap.

At Your Sewing Machine & Ironing Board

NOTE: There was a small typo on our original Medium Cord Wrap pattern. It said Velcro Front Side” on both ends. Oops! It should, like the Small Cord Wrap, say “Velcro Front Side on the left end and Velcro Back Side” on the right end. This has been corrected on the pattern download above, but you will notice this inconsistency within our in-step photos above and below. Go by the updated pattern and the steps as described and all will be well. These cuties have been made dozens and dozens … and dozens of times with great success. 

  1. Place the interfacing on the wrong side of the fabric. You just need enough interfacing the cover the area from which the pattern will be cut.
  2. Following manufacturer’s instructions, fuse in place.
  3. Pin the pattern in place. If you have a strong horizontal motif, make sure your pattern piece is straight. We folded our fabric wrong sides together in order to cut both layers at once.
  4. For each wrap, using the pattern, CUT TWO from the fabric (because we folded our fabric, we only made one cut).
  5. Place the front and back pieces right sides together. The edges should be flush all around.
  6. Pin together the layers, leaving a small opening for turning along one straight edge.
  7. Shorten your stitch length slightly. This will allow you to keep a smooth line around the curve.
  8. Using a ¼” seam allowance, stitch around the perimeter. Remember to lock your seam at either side of the small opening.
  9. Clip the corners and the curve and press open the seam allowance.
  10. Turn the wrap right side out through the opening. Use a long blunt tool to gently push out the corners so they are nice and sharp and to smooth the curve. A chopstick, knitting needle or point turner works well for this.
  11. Press flat, making sure to press in the seam allowance at the opening so it is flush with the sewn seam.
  12. The machine should be threaded with thread to best match your fabric in the top and bobbin.
  13. Re-set the stitch length to normal or even for a slightly lengthened stitch.
  14. Edgestitch around the entire perimeter. This keeps the seam from rolling and closes the opening used for turning.
  15. Find the Velcro®. Pull it apart into two pieces. The hook end (the rough end) should be centered along the straight end of the wrap. Pin or clip in place.
  16. Flip over the wrap. The loop end (the soft end) of the Velcro® should be centered on curved end of the panel. Pin or clip in place.
  17. You can also use the Velcro® drawing on the original paper pattern as a placement guide.
  18. Be sure you have placed the two halves on opposite sides of the wrap: one on the front and one on the back.
  19. Edgestitch the Velcro® in place along all four sides. Go slowly and carefully when stitching these two boxes, the stitching will be visible.


Project Design: Alicia Thommas
Sample Creation and Instructional Outline: Debbie Guild

Notify of

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business. When commenting, your name will display but your email will not.

Oldest Most Voted
Inline Feedbacks
View all comments
3 years ago

I have made many of these, but with a couple of changes. I use Kam snaps instead of Velcro, and I sew two buttonholes in the center to run the cord through so that I can’t misplace or lose the wrap while the cord is being used elsewhere. On a couple of them I added 3 tiny hot-fix rhinestones above the snap, just for some girly fun.

Liz Johnson
Liz Johnson
3 years ago
Reply to  Momo

@Momo — Such fun additions – thank you for sharing! It’s sounds a little closer to the wraps we made from sparkle vinyl as a holiday gift ideas. You might want to check those out as well. They have snaps as well but we cut our slits since the vinyl doesn’t fray. These are such useful little items. Here’s that link: https://sew4home.com/great-glittering-gift-ideas-fast-and-easy-with-dritz-hardware/

Liz Johnson
Liz Johnson
2 years ago
Reply to  Momo

Hi Kate — you are so welcome… these little cuties have always been popular 🙂

5 years ago

Thanks comes in handy.

Thanks comes in handy.

Translate »

You cannot copy content of this page



Enter your email address below to subscribe to the Sew4Home newsletter. Be the first to see new projects and patterns, helpful techniques, and new resources to enhance your sewing experience.


We will never sell, rent or trade your personal information to third parties.