A little wicked glamour and a wicked little spider come together to make a spellbinding Halloween mini mask. It’s what the most beguiling witches are wearing this season; combining spider web construction with a practical soft fleece backing. Your jeweled spider continues to weave its web while you bewitch those who dare to cross your path.

This mask fits an average adult witch. When you cut the pattern, use it to check and make sure the eye holes align properly. Adjust the holes if necessary before you cut your fabric.

The Haunted Mansion collection we used originally is no longer readily available, but there are lots of other bewitching new Halloween fabrics from which to choose.

The mask itself finishes at approximately 8¾” wide x 3¾” high, excluding the lace, which will depend on the width of ribbon you use. Ours was 2″.

Sewing Tools You Need

Fabric and Other Supplies

Click to Enlarge

  • Layer cake square (10″ x 10″) or scrap of fabric approximately 10″ x 5″
  • One 10″ x 5″ scrap of black polyester fleece – thick wool felt could also work
  • 1 yard of apx. 2″ wired-edge ribbon, we originally found our crazy web ribbon at Michaels
  • 1 yard soft black velvet cording, we found ours at Joann Fabric
  • 1 spider, we found our sparkly spider at Michaels
  • Thread to match or contrast; we used contrasting thread
  • Small sewing scissors, plus your junk drawer scissors to cut the wired-edge ribbon
  • Straight pins
  • Seam gauge
  • Sram ripper
  • Tape measure
  • Lint roller
  • Hand sewing needle

Getting Started and Pattern Download

  1. DOWNLOAD AND PRINT THE PATTERN.
    IMPORTANTThis pattern download consists of ONE 8½” x 11″ sheet. You must print the PDF file at 100%. DO NOT SCALE to fit the page. There is a scale box on the page to insure your printout is to scale. The page prints landscape.
  2. Cut out the pattern along the solid line.
  3. Place the pattern on the main fabric and cut ONE mask. We fussy cut the fabric to focus a spider right above the nose.
    Click to Enlarge
  4. Place the pattern on the polyester fleece and cut ONE mask. We used a lint roller to gently remove the loose fleece bits after cutting the pattern.
    Click to Enlarge
  5. Cut the yard of velvet cording in half to yield TWO 18″ lengths.
  6. Cut TWO 16″ lengths of wired-edge ribbon.
  7. Trim off ONE wired edge, approximately ¼” from the wire as shown below.
    NOTE: Remember to use your junk scissors on the wire ribbon so you don’t damage your good sewing scissors.
    Click to Enlarge
  8. Hand gather the raw edge of the ribbon with a hand needle and thread, using a loose running stitch. Then pin the gathered ribbon to the underside of the main fabric mask as shown in the photo below. It helps to use your fingers to create a similar gather along the wired edge first. Be sure to tuck the cut ends to the underside of the fabric so there are no wires poking out. Don’t be afraid to use plenty of pins to get the look your want.
    Click to Enlarge
  9. Hand baste the wired ribbon to the mask as shown below. This gets all those pins out of the way and makes finishing the mask easier.
    Click to Enlarge
  10. Turn the mask over and trim away any extra bits of ribbon that might interfere with the eye holes.
    Click to Enlarge
  11. Tuck a length of the velvet cord at either side of the mask. The ends should be placed between the fabric and ribbon layers so the cord lays across the ribbon. Align the cord with the eye holes as shown in the photo below. The ends should be inserted behind the fabric approximately ½”, making sure they don’t poke into the eyeholes. Pin in position. You want the cord to come straight out, not slant up or down.
    Click to Enlarge
  12. Place the fleece against the back of the mask, sandwiching the wired edge ribbon and velvet cording between the layers. Pin in place through all the layers.

At Your Sewing Machine

  1. Set your stitch length to its maximum, what you would normally use for machine basting.
  2. Sew the mask together. GO SLOWLY! Keep your needle in the down position and pivot as needed. You are sewing all the way around the outer edge of the mask as well as around each eye hole. Your seam should be about ¼” from the raw cut edge of the layers.
    NOTE: You can use either a matching or contrasting thread. We used bright red in the top and black in the bobbin to match the fleece. The plus side of using a matching thread is that your stitching will barely show, so any imperfections are difficult to see. The plus side of the contrasting thread is that it adds a little additional spark to the mask.
  3. Tie a single knot at each end of the velvet ties.
    Click to Enlarge
  4. Sew a spider to the mask approximately where shown in our photo. Or, use your imagination!
    Click to Enlarge

Hints and Tips

We tried on the mask as we sewed so we could: 1) check the eye holes in pattern, 2) insure the velvet cording felt like it was in the right position before sewing, and 3) hold the spider to finished mask to find the best position. Watch out for pins! And spiders.

Subscribe
Notify of
guest

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business. When commenting, your name will display but your email will not.

2 Comments
Newest
Oldest Most Voted
Inline Feedbacks
View all comments
Mealnie
Mealnie
28 days ago

This is such a cute pattern for Halloween; I shall try making it. Thank you!

Liz Johnson
Admin
Liz Johnson
27 days ago
Reply to  Mealnie

Hi Mealnie – Thanks! I hope you do make it – if so, we’d love to see a picture of you wearing it 🙂

  FOLLOW US!
Translate »