RenRib_Feb17_Leaderboard
Janome General-Leaderboard right

Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest Instagram

Sew4Home

Panel Place Mats with Large Motif Fabric

Printer-friendly versionSend by emailPDF version

By emphasizing a large motif and using a contrasting fabric for the borders, this place mat design creates the perfect frame for your favorite place setting. You’ll learn how to fussy cut to perfectly center the fabric’s motif, so whether you make two or twenty, each mat can be a perfect match. Our clever construction method starts as a tube, allowing a flatter finish with four lines of vertical topstitching.

We chose Tapestry Linen Canvas from the Menagerie collection by Rifle Paper Company for Cotton + Steel, which has lovely metallic accents. This is combined with a classic black denim from Robert Kaufman Fabrics. You want to select two fabrics of similar weights for the best balance.

Although the weights should be similar, don’t be afraid to experiment with more unusual substrate combinations. We settled on the lovely linen/canvas first and were then tasked with finding the best partner for it. Our first inclination was to go with another canvas or perhaps a smooth twill – both fine choices, but the denim, an outlier alternative, ended up being the best option. We mention our thought process not to say that you must use the exact same pairing, but rather to emphasize that mixing and matching is not a science… it’s an art, and it often means stepping away from the ordinary.

With the heavier canvas and denim, we didn’t feel the need to add batting – something we often do with our place mat projects to give a bit more tabletop protection for hot dishes and condensation from plates and glasses. Instead, a single layer of standard mid-weight interfacing backs all the panels.

As mentioned above, rather than the traditional method of stitching together front and back layers, we came up with a clever seam-and-roll construction option. You’ll cut one large panel from the denim and a smaller panel from the print. These panels are stitched into a tube, leaving a secret opening in one vertical seam that will be used later for turning right side out. The tube is rolled to perfectly center the fussy cut panel, then the rolled tube is flattened and stitched along the top and bottom. Read on for all the quick and easy steps.

Our motif is considered "large" because of its large repeat area, but the layout would work equally well for fabric with single large motifs, such as damasks, paisleys, and medallions. For more information on mastering the proper mixology of color and motif, check out our article: Top 10 Designer Tips for Blending Colors and Prints.

Each place mat finishes at approximately 15" high x 20" wide.

Sewing Tools You Need

Fabric and Other Supplies

Supplies shown are for TWO placemats - multiply as needed to fill your table.

  • ½ yard of 44”+ lightweight canvas, canvas-linen blend or similar; we used Tapestry Linen Canvas in Midnight from the Menagerie collection by Rifle Paper Company for Cotton + Steel
  • 1 yard of 44"+ wide mid-weight denim or similar (you want the weight to be similar to the canvas/canvas-linen); we used 8oz Black Washed Indigo Denim by Robert Kaufman
    NOTE: Denim is sometimes quite wide. If you can find a denim that is 58”+, you could get away with ½ yard by cutting the 29” panels side by side.
  • 1 yard of 45”+ wide mid-weight fusible interfacing; we used Pellon Décor Bond
  • All purpose thread to match fabric
  • Heavier thread in a slightly contrasting color for the topstitching; we used Coats Jeans/Topstitching thread in an orange/gold
  • See-through ruler
  • Fabric pen or pencil
  • Seam gauge
  • Seam ripper
  • Scissors or rotary cutter and mat
  • Iron and ironing board
  • Straight pins

Getting Started

As above, cuts shown are for TWO placemats.

  1. From the print fabric, fussy cut TWO 13” wide x 16” high rectangles.
  2. Find the exact center point of your large motif and then measure 6½” to the right of center and 6½” to the left of center, drawing a vertical line at each outer point.
  3. Cut along the outer drawn lines.
  4. Repeat, again finding the exact center point of your large motif, this time measuring 8” up from center and drawing a horizontal line, and 8” down from center, drawing a parallel horizontal line. Cut along these drawn lines.
  5. You now have a 13" x 16" center print panel with your large motif perfectly centered top to bottom and side to side. This fussy-cutting also allows you to match the front panels from placemat to placemat so they all have the exact same look.
  6. From the denim fabric, cut TWO 29” wide x 16” high rectangles.
  7. From the fusible interfacing, cut the following:
    TWO 12” x 15” rectangles for the center print panels
    TWO 28” x 15” rectangles for the denim panels, then from each of these panels, sub-cut TWO 4” x 15” strips. For each placement, you need one 20” x 15” panel and two 4” x 15” panels.

At Your Sewing Machine & Ironing Board

Fusing the interfacing

  1. Find the 13” x 16” center print panel and the 12” x 15” interfacing panel. Center the interfacing on the wrong side of the fabric panel so there is ½” of fabric showing beyond the interfacing on all sides. Following manufacturer’s instructions, fuse in place.
  2. Place the 29” x 16” denim panel wrong side up and flat on your work surface. Collect the three panels of interfacing for this panel (one at 20” x 15” and two at 4” x 15”). Starting from the right side of the fabric panel, place one 4” x 15” panel. There should be ½” of fabric showing beyond the interfacing along the right edge as well as both top and bottom. Lightly tack in place with your iron.
  3. Place the large (20” x 15”) panel next to the 4” panel. These two interfacing panels should be flush top and bottom and the center edges should butt almost together; you need just a crack to help facilitate the final fold of the roll-and-seam placement. Lightly tack in place with your iron.
    INSERT 2591-Photo 104
  4. Finally, place the remaining 4” x 15” panel in place along the left edge. Again, the top and bottom edges should be flush with the other interfacing panels, the inner edges should be almost touching, and the outer edge of this last panel should be ½” in from the left edge of the fabric panel.
  5. With all three panels positioned, fully fuse in place, following manufacturer’s instructions.
  6. The illustration below shows the positioning of the interfacing on the two panels.

Stitching, rolling, and final upper and lower seams

  1. Pin the print panel right sides together with the denim panel, aligning the 16” edges.

  2. Stitch together, using a ½” seam allowance, which means you should be stitching along the edge of the interfacing.

  3. Repeat to pin together the remaining 16” edges, creating a tube. But on this second seam, leave an approximate 4-5” opening at the center of the seam.
  4. Stitch together, using a ½” seam allowance. Remember to lock the seam at either side of the 4-5” opening.
  5. With the tube still wrong side out, roll it to center the print panel. This means there should be 4” of denim to either side. As shown below, the 4” is measured from the seam to the outer fold.

  6. Pin in place across the top and bottom of the placemat. Take the time to check that your side panels are truly even from top to bottom, measuring each corner. The seam allowances should be pressed together and toward the side denim panels.

  7. Using a ½” seam allowance, stitch across the top and bottom. These seams are what secure the print panel in its centered position.

  8. Clip the corners and press open the seam allowances top and bottom.

  9. Turn the placemat right side out through the opening in the one vertical seam.

  10. Use a long, blunt toot to gently push out all the corners so they are nice and sharp. A knitting needle, chopstick or point turner all work well. Press the placemat super flat, including the opening in the vertical seam. Remember, those vertical seam allowances should be facing the outer denim panels. Pin the opening closed.

Final topstitching

  1. Re-thread the machine with the contrasting, heavier thread in the top and bobbin. Lengthen the stitch. If possible, attach a Quarter Inch Seam foot.
  2. Topstitch along each outer folded edge from top to bottom, ¼” from the edge.

  3. Topstitch ¼” from each inner vertical seam within the denim panel. This topstitching closes the opening used for turning.

  4. For all topstitching seams, when both starting and finishing, use a lockstitch, a very neat backstitch, or leave your thread tails long and knot to secure. The top and bottom of each seam need to be right at the edge of the mat and you want as neat a start and finish as possible.

Contributors

Project Design: Alicia Thommas  
Sample Creation: Debbie Guild

Section: 

Comments (10)

MAP said:
MAP's picture

A simple and quick way to sews with the seasons. Thanks to whom ever thought it up.

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@MAP - Thank you. Let us know if you make a set for an upcoming season.

Coastal Sewist said:
Coastal Sewist's picture

I LOVE these, thank you!!! Now scheming on my fabric choice, fortunately I can "shop" in my own stash and don't have to go to town. The sooner to get to sewing, she says gleefully :-)

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Coastal Sewist - Thanks! We're so glad you love the pattern. Let us know how yours turn out. 

francer said:
francer's picture

Your placemats are gorgeous, thank you very much again for your clear and professional instructions.  I have been looking for a pattern for what is called in French: "vis-à-vis" pattern. Since I like your idea so much for today's project I was wondering how I could modify it to make a vis-à-vis. (A vis-à-vis is like two placemats, joined together and making them long to reach each side of the table for people to sit at the table face to face. Then, there would be another from one end of the table to the other end much similar to a table runner but the ends are in fact the placemats for the persons sitting at each end. This very long vis-à-vis would be placed on top of the others that cross over the table to also act as a table runner. Hope I make myself understandable as I am French and trying to describe the vis-a-vis! Sorry but not easy!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@francer - I do understand what you're saying, and describing it like a table runner is good. I don't think the roll-and-seam method we're using here would be the best for what you are wanting to make because you want to insert more than one center feature panel. I'd suggest going with a traditional top and back layered construction method. You'd want to create the top with as many "featured settings" as needed for your size of table. Map this out with three individual pieces per "setting" - one center and two outer panels. As you're describing, there then may need to be additional solid panels in between these featured settings to create the proper spacing. Stitch together all the panels into one long piece for the top. Then, simply cut one solid panel for the back to match, and seam front to back to finish. 

Sunnie Mitchell said:
Sunnie Mitchell's picture

Love the construction method, thank-you for making it so simple! Re fabric weight mixing, I've had some success when trying to use a light weight with a medium to heavy(ish) fabric by using a solid colour in the heavier weight to make the lighter one match the heavier one. 

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Sunnie - Thanks! We thought the roll-and-seam was a nice change of pace. Not sure if I'm completely understanding your weigth balancing comment. Do you mean using a lining behind the lighter weight?

Sunnie Mitchell said:
Sunnie Mitchell's picture

Sorry, I knew I should have described it better:) Lining, yes - cutting the lighter weight and a lining in the heavier weight in the same size using a solid colour that will not show through the lighter weight. I baste the two pieces together a quarter inch inside the seam allowance so I can use the lighter fabric, now bolstered by the solid piece, 'as one' with my heavier weight decorator (or garment making) fabric. Once it's all sewn together I unpick the basting. I think it's a vintage quilter and garment sewing tip I picked up from one of the 1930s-1950s era sewing books I haunt our local charity and used book shops for. I live in the UK, it is truly vintage 'home craft' book heaven here. 

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Sunnie - Thanks for taking the time to clarify. I totally get it now, and yes, that is a great option to simply try to layer interfacing in order to get the two weights to match up. 

Add new comment

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business.
By submitting this form, you accept the Mollom privacy policy.