Janome Red Tag Event thru 2-28-19
s4h-janome-HMC-9450-LB-728x90_Feb2019

Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest Instagram

Sew4Home

Slim Crossbody Shoulder Pouch: Dritz Belting and Hardware

Printer-friendly versionPDF version

We all seem to love the little things: kittens and puppies, babies in tiny baby gear, even mini muffins are cuter and more irresistible than their full size counterparts. So it goes for smaller pouches meant to hold just the necessities when you’re out and about. It’s one of our most popular project categories! We continue to have a blast with the new Dritz Belting, using it this time in the colorful 1” width to create an adjustable strap for a handy crossbody shoulder pouch.

Our slim design is meant to be able to be worn either over or under a jacket or other outerwear. The Dritz Belting strap is fully adjustable, so the pouch can be shortened to fit snuggly against your side. When worn under a jacket, it can function as a travel document pouch, firmly held in place just under your upper arm, a little like a holster.

Loosen the Belting to wear the pouch crossbody over a jacket or activewear top. Position the pouch to rest either across the front or out of the way across the back. Again, its slim profile allows it to comfortably mold against your body.

Slip both arms through and it can even be slung around the waist like a fanny pack. The length of the strap means that on most people, it will sit a bit below the natural waistline when cinched all the way up.

The new Dritz 1” Belting is 100% polypropylene and comes in 20 colors. We picked a Royal Purple, coordinating the zippers, zipper pulls, and piping  to match. We then chose a classic nickel finish for the Dritz Slide Adjuster and Rectangle Ring that work together to create the adjustable strap.

The main pouch is lined with wipe-clean ripstop nylon – always a plus with anything meant to be used outdoor. For the exterior we recommend a standard cotton twill, and although you could launder the pouch on a delicate setting inside a mesh bag or similar, we recommend spot cleaning over the the agitation of a washing machine. In either case, allow the case the air dry rather than tumble drying. You could also protect the finished pouch with Scotchgard or similar.

There are two, full-width pockets on the front of the pouch. The upper zipper opens to the main ripstop lined interior and is the full 8” in depth. The lower zipper is unlined and includes a inverted box pleat that allows the pocket to expand to hold dimensional items, like keys, a small flashlight, personal alarm, or garage door opener.

An Extra Large Dritz Eyelet at the center top of the back panel allows you to snake out earbuds without opening either zipper. Simply drop in the phone jack end up, then feed the adapter through the grommet into the jack and zip closed. Pop in your earbuds and rock on. Of course, if you’re all cutting edge with your bluetooth buds, the grommet can be skipped and the back panel left completely solid.

At just 4½” wide, the two polyester zippers will need to be cut to size, We show you the easy steps. The good news with our process, you can stitch the zipper in place without opening and closing the zipper!

We personalized our pouch with a Sew4Home label. Add your own label or consider machine or hand embroidery to customize with initials.

Our thanks to Dritz for providing us with access to their great new products and sponsoring these project instructions so they are free to you! Dritz always has wonderful ways to keep your sewing easier and more creative. To find out more, we invite you to visit their website or blog; or follow them on Pinterest, Instagram, TwitterFacebook, and YouTube

Our Slim Crossbody Shoulder Pouch finishes at approximately 4½” wide x 8” high. The 60” of belting cinches down to 30”.

If you love this Belting Pouch, you may also want to check out our other projects featuring Dritz Belting: Unisex Belted Half Aprons, Fast and Easy Gym Tote, and Washed Canvas Tote with Belting Handles and Drawstring Lining.

Sewing Tools You Need

Fabric and Other Supplies

  • 2 yards (one package) of Dritz 1” Belting; we used purple
  • ONE Dritz Slide Adjuster; we used nickel
  • ONE Dritz Rectangle Ring; we used nickel
  • ONE Dritz Extra Large Metal Eyelet with Setting Tools; we used nickel
  • ¼ yard of 45”+ wide twill or similar; we used a sportswear stretch twill in Sunflower
  • ¼ yard of 45”+ wide ripstop nylon or similar; we used ripstop nylon in gray
  • ¼ yard of 20”+ wide lightweight fusible interfacing; we used Pellon Shape-Flex
  • TWO 7”+ standard zippers in a color to match the Dritz Belting; we used purple
    NOTE: As you’ll see in the instructional photos below, we started with a much longer zipper cutting it to fit. This is easy with a polyester zipper and is a helpful option when it’s hard to find short zippers.
  • 1 yard of packaged piping in a color to match the Dritz Belting; we used Wrights Bias Tape Maxi Piping in Purple
  • Thin cotton cording for the zipper pulls in a color to match the Dritz Belting; optional – we used purple cotton jewelry cord
  • Small scrap of felt or fusible fleece; optional for eyelet insertion – you need just a 2” square
  • All-purpose thread to match fabric
  • See-through ruler
  • Fabric pen or pencil
  • Iron and ironing board
  • Pressing cloth
  • Scissors
  • Rotary cutter and mat
  • Seam gauge
  • Seam ripper
  • Straight pins
  • Small hammer to set eyelet; we suggest a ball peen hammer or leather mallet
  • Heavy metal, stone or wooden block to use as a cutting and hammering surface; we like to use a small granite block

Getting Started and Pattern Downloads

  1. Download and print out our TWO pattern sheets: Pouch Body, Pouch Pocket, and Pocket Top Band, which have been bundled into one PDF to make the download easier. The Pocket and Pocket Top Band are combined onto one sheet.
    IMPORTANT: Each pattern page is ONE 8½" x 11" sheet. You must print the PDF file at 100%. DO NOT SCALE to fit the page. There is a guide rule on each page so you can confirm your final printout is to scale.
  2. Cut out all three pattern pieces along the solid line. 
    NOTE: When you have a distinct front and back to any of your fabrics (this includes the fusible interfacing) and an asymmetrical shape, such as our Pouch Body pattern, you need to remember that the two pieces must be mirror images of one another so they will layer together correctly when seaming to finish. The easiest way to accommodate this is to fold your fabric/interfacing and use the pattern to cut two Pouch Body panels at one time.
  3. From the exterior fabric, cut the following:
    Using the pattern, cut TWO Pouch Body panels
    Using the pattern cut ONE Pouch Pocket panel
    Using the pattern, cut ONE Pocket Top Band

  4. From the lining fabric, using the pattern, cut TWO Pouch Body panels.
  5. From the fusible interfacing, using the pattern, cut TWO Pouch Body panels.
  6. The image below shows all the panels required for one pouch.

  7. From the Dritz Belting, cut ONE 60” length and ONE 2” length.
  8. The piping will be cut to length during construction.
  9. Using the guide lines of the pattern pieces, make small snip into the seam allowance of each panel to mark the placement of the straps, zippers, and pleats.

At Your Sewing Machine & Ironing Board

Create the pleated pocket

  1. Find the exterior pocket panel. As noted above, you should have made five little snips marking the pleats within both the upper and lower seam allowances. Fold the outer lines toward the center line and pin in place at both the upper and lower edges of the pocket. This creates an inverted box pleat. Pin in place. If you are brand new to pleating, take a look at our full Box Pleat Tutorial.
  2. Machine baste in place within the seam allowance.
  3. Press to set the pleats.
  4. Find one of the two zippers and the Top Pocket Band.
  5. Place the pleated pocket right side up and flat on your work surface. Place the zipper right side down along the upper edge of the pocket. The zipper stop should be ½” in from the left raw edge of the pocket. The upper edge of the zipper tape should be ¼" down from the upper raw edge of the pocket. If your zipper is longer than necessary as ours was, concentrate on the position of the zipper stop; the zipper should be closed and completely out of the way to the right at this point. Pin in place.
  6. Attach a Zipper foot.
  7. Thread the machine with thread to best match the exterior fabric in the top and bobbin.
  8. Using a ½” seam allowance, stitch across the zipper.
  9. Remove the pocket from the machine.
  10. Trim the fabric back so it is flush with the zipper tape.
  11. Re-attach a standard presser foot.
  12. Finish the edge of the zipper tape/fabric with your favorite machine finish. We used a simple zig zag.

    NOTE: This finishing step is recommended because the front pocket is designed without a lining and so we wanted a clean finish inside the pocket.
  13. Finger press the zipper up and away from the pocket.
  14. Slightly lengthen the stitch.
  15. Edgestitch along the zipper within the pocket fabric.
  16. Find the Pocket Top Band.
  17. Place it right sides together with the remaining side of the zipper tape. The seam allowance for the Pocket Top Band is ¼", so for this layering, the edge of the zipper tape should be flush with the the edge of the fabric. Pin in place.
  18. Re-set the stitch length to normal.
  19. Similar to how you attached the opposite side of the zipper, but using a ¼" seam allowance, stitch across and then finish the edge.
  20. Finger press the band up and away from the zipper.
  21. Edgestitch along this side of the zipper, using the same slightly lengthened stitch as above.
  22. Flip over the pocket. Press back the upper raw edge of the top band ¼”, which means the raw edge should end up aligned with the zipper tape.

Interface the main panels and attach the front pocket

  1. Find the two Pouch Body panels and the two matching pieces of interfacing. Place the interfacing on the wrong side of each fabric panel. All edges should be flush. Following manufacturer’s instructions, fuse in place.
  2. Place the two interfaced exterior panels right side up and flat on your work surface. As mentioned above, these two panels should be mirror images of one another.
  3. Place the pleated pocket on top of one panel, aligning the side and bottom raw edges of the two pieces.
  4. Pin the pocket to the pouch along the top of the pocket band.
  5. Using the same slightly lengthened stitch, edgestitch the band in place along this upper folded edge.
  6. Slide the zipper pull down toward the zipper stop, stopping in the middle of the pocket at the pleat.
  7. Machine baste the zipper to the pouch along each side of the pouch within the seam allowance. At the bottom of the zipper, this means you are stitching just to the left of the metal stop. At the opposite end, simply baste within the ½” seam allowance.
  8. Trim the zipper tape even with the right side edge of the pouch.

Attach the upper zipper

  1. You should have made small snips in the seam allowance to mark the ends of the upper cutting line on the main exterior panel as well as the lining. If you did not, do this now. Use a ruler to draw in a horizontal line connecting the snips on both the exterior front panel and one of the lining panels. The remaining exterior panel and lining panel remain un-marked and un-cut.
  2. Cut along the drawn lines.
  3. Find the second zipper.
  4. Find the sliced front panel. Set the smaller upper section off to the side.
  5. Place the zipper right side down along the top raw edge of the larger lower section. As above, the zipper stop should be ½” in from the left raw side edge of the fabric panel and the excess zipper should extend, closed, off the right edge of the panel. For this second zipper placement, the top zipper tape should be flush with the fabric panel. Pin in place.
  6. Find the larger lower section of the lining. Place it right sides together with the exterior panel, sandwiching the zipper between the layers. Re-pin through all three layers, make sure all the layers stay flush.
  7. Re-set the stitch length to normal. Using a ¼” seam allowance, stitch across through all the layers.
  8. Fold the lining and the exterior panels down and away from the zipper so the two panels are now wrong sides together and the remaining edge of the zipper tape is sticking up.
  9. Slightly lengthen the stitch to match your previous edgestitching and edgestitch along the bottom of the zipper within the exterior panel.
  10. Find the two smaller upper sections: the exterior piece and the lining piece.
  11. Place the lower exterior panel right side up and flat on your work surface.
  12. Place the upper exterior piece right sides together along the top of the lower exterior panel. Pin in place.
  13. Flip over the panel and place the upper lining piece right sides together along the top of the lower lining panel.
  14. The zipper tape is now sandwiched between two layers on the front and two layers on the lining. Re-pin through all the layers.
  15. Re-set the stitch length to normal. Using a ¼” seam allowance, stitch across.
  16. Fold the small lining and the exterior panels up and away from the zipper so they are now wrong sides together.
  17. Slightly lengthen the stitch to match your previous edgestitching and edgestitch along the top of the zipper within the fabric panel through all the layers.
  18. As you did with the lower zipper, move the zipper pull to the center of the panel and machine baste across both ends, then trim away the excess zipper so the zipper is flush with the side of the panel.

Attach the Dritz Belting and Rectangle Ring

  1. Find the 60” and 2” lengths of Dritz Belting along with the one Dritz Rectangle Ring
  2. Fold the 2” section around the Rectangle Ring so the raw ends are flush.
  3. Place the front panel right side up and flat on your work surface.
  4. You should have made small snips in the seam allowance of the exterior front panel to mark the position of the belting ends. If you did not, do this now.
  5. Pin the Rectangle Ring Belting loop to the pouch front along the lower right side, between the small snips. Pin in place.
  6. Pin the 60” length of Belting to the upper edge of the pouch between the small snips near the left corner. Pin in place.
  7. Machine baste the 60” length of Belting in place within the ½” seam allowance.
  8. Machine baste the Rectangle Ring Belting loop in place within the ½” seam allowance.

Assemble the back panel with piping and grommet

  1. Find the exterior back panel and lining back panel. Place the two panels wrong sides together.
  2. Pin together the layers all around.
  3. Find the piping. Starting at the lower square corner, place the piping against the exterior side of the back panel. The stitching on the piping insertion tape should sit at the ½” seam line, which means the edge of the insertion tape will sit slightly in from the raw edge of the fabric panel. Pin the piping in place.
  4. Attach a Piping foot if possible. This foot rides over the piping cord and produces a straight, tight stitch. If you don’t have this specialty foot, a Zipper foot is another good option that allows you to get as close as possible to the piping cord.
  5. Re-thread the machine with thread to best match the piping in the top and bobbin.
  6. Starting the stitching ” in from the corner, machine baste the piping around the entire perimeter of the back panel.
  7. Clip into the piping to fit the upper and lower curves.
  8. Also clip into the remaining upper square corner.
  9. This clipping helps produce a much more precise seam allowance for a much more consistent reveal when turned right side out.
  10. Stop the stitching when you return to the first corner.
  11. Trim away the excess piping. Position the ends of the piping side by side and stitch across the corner diagonal just within the seam allowance. With a thin, flat pouch like this, we feel this is a better finish to the piping than a more traditional butt-and-wrap finish. The flattened piping will disappear into the bottom corner. 

    NOTE: If you are brand new to working with piping, check out our full tutorial on making your own and finishing options.
  12. Place the piped exterior back panel right side up and flat on your work surface.
  13. Find the paper pattern, which has a placement marking for the one eyelet. Using sharp small scissors, trim away the small inner circle on the paper pattern.
  14. Place the pattern over the pouch back, matching the corners and the curves, and mark the placement circle onto the pouch back.
  15. Following manufacturer’s instructions or our own great step-by-step tutorial on installing metal grommets and eyelets, add the one Dritz Extra Large Eyelet at the marked point.

    NOTE: The Dritz Extra Large Eyelet is meant for multiple layers of mid to heavyweight fabric. If your layers are not thick enough to properly fill the eyelet, it can be hard to join the two halves without damaging the hardware. In this case, we recommend adding an extra layer of felt or fusible fleece between the exterior and lining prior to pinning together those back panel layers. Then apply the eyelet.

Layer front to back to finish and finish adjustable strap

  1. Open the upper zipper about half way. Pass the end of the Belting through the zipper opening.
  2. Place the pouch front to pouch back right sides together; all edges should be flush all around. The Rectangle Ring Belting loop will be sandwiched between the layers, and as noted above, the long length of Belting will extend outside the pouch through the front zipper. Pin together all around.
  3. Place the layers under the presser foot with the back panel facing up so you can see the machine basting seam of the piping. Using this seam as your guide line, stitch all the way around the perimeter of the pouch through all the layers. Remember to pivot at the corners and firmly backstitch at the end of the seam.
  4. Trim back the seam allowance to approximately ¼” and clip the curves, but do not trim the ends of the piping.
  5. Turn the pouch right side out through the zipper opening. Gently pulling on the Belting will help you turn. Use a long, blunt tool to square the corners and smooth the curves. Press flat.
  6. If necessary, re-thread the machine with thread to best match the Dritz Belting in the top and bobbin. Slightly lengthen the stitch.
  7. Find the Dritz Slide Adjuster. Thread the raw end of the Belting up and over the center bar of the Slide Adjuster.
  8. Next, feed the raw end of the Belting through the Rectangle Ring from front to back.
  9. Finally, insert the raw end of the Belting back through the center bar of the Slide Adjuster. You are again inserting up and over the bar but are now working beneath the first layer of Belting. Bring the raw end back on itself about 1”. Turn under the raw end ¼” and stitch in place through all the layers.
  10. If adding the optional zipper pull, cut two 7” lengths of cord. Fold the cord in half and insert the loop through the zipper pull. Thread the ends of the cord through the loop and pull tight. This is just how you would attach a price or gift tag. Knot the ends together and trim to an even length.

We received compensation from Dritz® for this project, and some of the materials featured here or used in this project were provided free of charge by Dritz®. All opinions are our own.

Contributors

Project Design: Alicia Thommas   
Sample Creation and Instructional Notes: Michele Mishler

Tags: 

Section: 

Comments (6)

Rashmi said:
Rashmi's picture

Is it possible to make this bag with normal quilting fabric, as I would like to use up fabric I already have rather than go and purchase more. Thank You.

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Rashmi - a quilting weight cotton is not our recommendation. You could certainly try to experiment with stabilizer to give the cotton more stability, but without testing that, we can't give you a guarantee it would turn out to your liking. And, because the front pocket has no lining, it definitely would not hold up well without stabilization. That means you'd probably want to add a lining for that pocket, which is possible, but does make the pleat more difficult. That said, anything is possible if you experiment with layering, it just would not be our choice. 

Coryb said:
Coryb's picture

What a great idea! The pouch would be a great gift for guys and gals of any age. I want one for myself!  Thanks for another great pattern!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Coryb - Thanks so much - it would be a great gift for anyone... but you should make one for yourself to start 

Linda Powell said:
Linda Powell's picture

I printed this pattern out but it came out smaller than the finished dimensions the project calls for.  It printed out 4" by 61/2". The finished bag should be 8" high by 41/2" wide. Directions say not to size or scale it but my phone will never fit in this. Can you tell me how to enlarge to what %?  Please help!!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@ Linda - The pattern is delivering correctly from the site, so the problem must be how your printer is choosing to print it out. It is likely that it is set to try to shrink the pattern to "better fit" on the page. Make sure, in your browser window, that "shrink to fit" or "scale to fit" are not checked. You want it to print "full size" or "100%" -- You shouldn't need to do any complicated math to enlarge; just make sure your printer is set to give you a full size print out.