New Janome General-Leaderboard Left

Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest Instagram

Sew4Home

Haunted Halloween Jeweled Spider Mask

Printer-friendly versionSend by emailPDF version

A little wicked glamour and a wicked little spider come together to make a spellbinding Halloween mask. It's what the most beguiling witches are wearing this season; combining spider web construction with a practical soft fleece backing. Your jeweled spider continues to weave its web while you bewitch those who dare to cross your path.

This mask fits an average adult witch. When you cut the pattern, check to make sure the eye holes align properly and adjust if necessary before you cut your fabric.

The Haunted Mansion collection we used originally is sooooo last Halloween. Below are a couple 2015 options spotted at Fabric Depot. The purple option is Purple Bats from the wonderful Chillingsworth's Spooky Ride collection by Andover Fabrics. For a more monochromatic option, we like Skulls from the Glow in the Dark Halloween collection by Timeless Treasures

   

Sewing Tools You Need

Fabric and Other Supplies

Click to Enlarge

  • Layer cake square (10" x 10") or scrap of fabric 10" x 5": we used a layer cake square in Purple Wallpaper from the Haunted Mansion collection by Sanae for Moda
  • One 10" x 5" scrap of black polyester fleece
  • 1 yard wired-edge ribbon, we found our crazy web ribbon at Michaels
  • 1 yard soft black velvet cording, we found ours at Jo-Ann Fabrics
  • 1 spider, we found our sparkly spider at Michaels
  • Thread to match or contrast
  • Small sewing scissors, plus your junk drawer scissors to cut the wired-edge ribbon
  • Straight pins
  • Tape measure
  • Lint roller

Getting Started

  1. Download and print the pattern
    IMPORTANTThis pattern download consists of ONE 8½" x 11" sheet. You must print the PDF file at 100%. DO NOT SCALE to fit the page.
  2. Cut out the pattern along the solid line.
  3. Place the pattern on the main fabric and cut ONE mask. We fussy cut the fabric to focus a spider right above the nose.
    Click to Enlarge
  4. Place the pattern on the polyester fleece and cut ONE mask. We used a lint roller to gently remove the loose fleece bits after cutting the pattern.
    Click to Enlarge
  5. Cut the yard of velvet cording in half to yield TWO 18" lengths.
  6. Cut TWO 16" lengths of wired-edge ribbon
  7. Trim off ONE wired edge, approximately ¼" from the wire
    NOTE: Remember to use your junk scissors on the wire ribbon so you don't damage your good sewing scissors. 
    Click to Enlarge
  8. Hand gather the raw edge of the ribbon with a loose running stitch. Then pin to the underside of the main fabric mask as shown in the photo below. It helps to use your fingers to create a similar gather along the wired edge first. Be sure to tuck the cut ends to the underside of the fabric so there are no wires poking out. Don't be afaid to use plenty of pins to get the look your want.
    Click to Enlarge
  9. Hand baste the wired ribbon to the mask as shown below. This gets all those pins out of the way and makes finishing the mask easier.
    Click to Enlarge
  10. Turn the mask over and trim away any extra bits of ribbon that might interfere with the eye holes.
    Click to Enlarge
  11. Pin a length of the velvet cord to either side of the of back of the mask. The ends should be placed between the fabric and ribbon layers so the ribbon lays across the ribbon. Align the ribbon with the eye holes as shown in the photos below. The ends should be inserted behind the fabric  approximately ½". Pin in position. You want the cord to come straight out, not slant up or down.
    Click to Enlarge
  12. Pin the fleece to the back of the mask, sandwiching the wired edge ribbon and velvet cording between the layers. Pin in plae.

At Your Sewing Machine

  1. Set your stitch length to its maximum, what you would normally use for machine basting.
  2. Sew the mask together. GO SLOWLY! Keep your needle in the down position and pivot as needed. You are sewing all the way around the outer edge of the mask as well as around each eye hole. Your seam should be about ¼" from the cut edge of the layers.
    NOTE: You can use either a matching or contrasting thread. We used bright red in the top and black in the bobbin. The plus side of using a matching thread is that your stitching will barely show, so any imperfections are difficult to see. The plus side of the contrasting thread is that it adds a little additional spark to the mask.
  3. Tie a single knot at each end of the velvet ties.
    Click to Enlarge
  4. Sew a spider to the mask approximately where shown in our photo. Or, use your imagination!
    Click to Enlarge

Hints and Tips

We tried on the mask as we sewed so we could: 1) check the eye holes in pattern, 2) insure the velvet cording felt like it was in the right position before sewing, and 3) hold spider to finished mask to find the best position. Watch out for pins! And spiders.

Section: 

Comments (0)

Add new comment

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business.
By submitting this form, you accept the Mollom privacy policy.