Dritz Leaderboard_2019_Visit Dritz_new logo

Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest Instagram


Dream Big Reversible Cuddle Baby Blanket with Satin Ruffle

Printer-friendly versionPDF version

A plush baby blanket with a lush satin ruffle – it just doesn’t get any cozier than this! We combined two adorable Cuddle minky prints from Shannon Fabrics: Dream Big in Banana from their Sweet Melody Designs collection with Alotta Dots in Graphite. Around the edge is a deep ruffle in a Silky Satin Solid, also by Shannon Fabrics. It’s an absolutely beautiful blend of soft and smooth textures. In fact, I’m a little tempted to request my own softee security blanket; there’s not a time limit on those, right? 

This type of fleece can be a bit slippery on the back; so with wrong sides together, we knew there could be a problem with the layers shifting. However, we didn't want to add any quilting stitches to hold the layers together as we felt it would take away from the smooth look of the finished blanket. 

Instead, we came up with a clever solution: there's a secret layer of flannel in between the two layers of Cuddle. The double-napped flannel (brushed on both sides) keeps the two layers from shifting and adds a little extra oomph and insulation as well.

Make sure you pre-wash your flannel. Otherwise, it could shrink up more than the Cuddle and cause your lovely blankie to twist and turn after laundering.

As baby shower gifts go, there really is no such thing as too many blankets. Before babies are completely mobile, you always need something to cover a surface and make a soft, safe area for playing, napping or eating. The more blankets the merrier, and when it’s as cute as this one, you know yours will be the one Mom and Dad reach for time and again. 

Shannon’s Dream Big print comes in the light banana yellow we used as well as a sweet blush pink and classic baby blue. 


Even with our clever layering trick, you will still be sewing through a number of somewhat slippery layers. Make sure you have a machine with a good feeding system, like the AcuFeed™ Flex Layered Fabric Feeding System, built into the Janome Skyline S7 we used for our sample. 

The blanket finishes at approximately 34” x 34” with a 2½” ruffle all around.

Sewing Tools You Need

Fabric and Other Supplies

NOTE: Amounts shown below are for ONE blanket. Multiply as needed for twins, triplets and beyond.

Getting Started

  1. From the front fabric cut ONE 35" x 35" square.
  2. From the back fabric cut ONE 35" x 35" square.
  3. From the cotton flannel fabric, cut ONE 35" x 35" square.
  4. Layer the panels: back panel wrong side up, flannel, front panel right side up. 
  5. Using a small glass or cup as a template, draw in a matching curve at each corner.
  6. Cut out the curve through all the layers.
  7. From the ruffle fabric, cut SIX strips 6" x width of fabric (WOF). 
    NOTE: We used the rule of thumb that says your ruffle needs to be approximately 2½ times the length of the edge to which you're applying the ruffle. Since our blanket will be approximately 34" square when finished, we multiplied 34" by 4 to get 136".  Then we multiplied 136" by 2.5" to get 340". Finally, we divided this new total length by the width of fabric (WOF) to get the number of strips we'd need. In our sample, that meant dividing 340" by 60". This equaled 5.66, which we rounded up to 6. We wanted a 2½" finished ruffle, so we knew our ruffle strips would need to be 6" to account for folding the strip in half plus a ½" seam allowance (6 strips at 6” used up our one yard of satin). After all this math-noodlin', we cut our SIX 6" x WOF strips. Sewn together, this gave us approximately 357½" of ruffle fabric to work with. If you are new to this technique, you can check out our tutorial on machine gathering.

At Your Sewing Machine & Ironing Board

Create the ruffle

  1. Sew all the 6" strips together end to end. To do this, place two strips right sides together and stitch along the 6" edge, using a ½" seam allowance. Repeat to create one long strip. Press all seam allowances open and flat.
  2. Fold and press this long ruffle piece in half lengthwise, wrong sides together.
  3. Hem one end of ruffle. To do this, turn one end under ¼" and press, turn under another ¼" and press again, then sew in place close to the folded edge. 
  4. Starting just past the narrow hem, ruffle the entire folded strip. Remember, your goal is to gather the strip to the approximate length of the four sides of the blanket (136"). Leave some extra length for overlapping to finish the ends. No need to have an exact measurement, just give yourself plenty to work with.

    This is a LOT o' ruffling, which is why we opted to use the Ruffler attachment for our Janome machine. These contraptions look intimidating but are easy to use. Most machine manufacturers offer something similar to what we show, and the Janome version is actually made to fit both Janome machines as well as machines from other manufacturers. We have a short technique article on using this accessory. If you don't have a ruffler attachment, you can ruffle the traditional way with two lines of machine basting. With this much length, it's a good idea to do the machine basting in easy-to-work-with sections of about 18" or so. Again, you can take a look at our tutorial on machine gathering
  5. If you are using a Ruffler attachment, note that satin fabric can be slippery. It’s best to pin the raw edges with the head of the pin facing to the raw edge side of the ruffle, and with a pin set about every 3-4". This will help keep the satin fabric from twisting as it is fed into the ruffler. Be sure to remove pins as you feed the satin fabric into the ruffler!

Place ruffle

  1. Find the front panel, removing it from the flannel and the back panel layers. Place it right side up and flat on your work surface.
  2. Starting with the hemmed end, and with the back of that hem against the right side of the blanket (right side to right side), pin the ruffle to the right side of the front panel. Align the raw edges of the ruffle with the raw edge of the fabric. 
  3. When you have about six inches remaining before the beginning and the end meet, lay out the end of the ruffle so it overlaps the beginning by about 2½". 
  4. Cut off the excess ruffle, then fold a hem into this end in the same manner as the hem at the head of the ruffle. 
  5. Stitch the hem in place. If you've used a Ruffler attachment, you'll need to switch back to your regular presser foot. 
  6. Overlap the two finished ends so the ruffle lays flat and finish pinning. 
  7. Machine baste the ruffle in place around all four sides. 
    NOTE: We engaged our AcuFeed™ Flex feeding system. Working with a built-in feeding system or a Walking or Even Feed foot is best for the remainder of the construction. 

Assemble the layers

  1. Find the back panel and the flannel. Layer the flannel against the wrong side of the back panel. The raw edges of both layers should be flush all around.
  2. Machine baste the flannel square to the wrong side of the back blanket panel, using a ¼" seam allowance. 
  3. Carefully pin the extra ruffle fabric away from the corners so it does not get caught up in the stitching when the front and back are sewn together,
  4. Layer the flannel/back fabric panel and the ruffle/front fabric panel right sides together. The ruffle is now sandwiched between the layers.
  5. Pin in place, using plenty of pins. Leave a 3-4" opening along one side for turning.
  6. Using a ½" seam allowance, stitch through all layers around all four sides, remembering to leave that 3-4" opening for turning. Stitch slowly, smoothing the layers as you go; this will help insure your ruffle stays flat. As mentioned above, we are still using our built-in AcuFeed™ Flex feeding system.
  7. Clip all four corner curves. Then, trim the flannel/back fabric close to the seam, but be careful not to cut into your stitching. Don't trim the ruffle/front fabric.
  8. Turn blanket right side out through the opening. 
  9. Pull out the ruffle into position, and press from each side. Use a pressing cloth/towel and low heat as the Cuddle does NOT react well to direct or high heat from an iron. It will ruin the nap and any embossing in the fabric.
  10. Use a long, blunt-end tool to round out the corner curves; a long knitting needle or chopstick works well.
  11. Fold in the raw edges of the opening so they are flush with the sewn seam. Finger press. Pin in place.
  12. Hand stitch the opening closed. Cuddle is great for hiding hand stitching; it simply disappears into the nap.


Project Design: Alicia Thommas   
Sample Creation and Instructional Outline: Debbie Guild


Comments (22)

Linda L. said:
Linda L.'s picture

Why in step 2 under 'Place ruffle' do you place the wrong side of ruffle against the right side of the fabric? It seems to me they should be right sides together, what am I missing?

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Linda - They should be right sides together. That small correction has been made above. However, since both ends are hemmed and overlapped, and the blanket is reversible - either way really works. Let us know how yours turns out 

Robyn H said:
Robyn H's picture

No matter what tutorial I follow, I always have the same problem when I make a Minky blanket -- one side of the blanket seems to have more fabric then the other, and won't lay flat. It doesn't matter whether I'm using flannel/Minky, cotton/Minky, or Minky/Minky. I'd really appreciate any suggestions on how to solve this problem! 

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Robyn - It sounds like your layers are shifting when you are sewing. As mentioned in this tutorial, when we sew two layers of luxury fleece, we like to add a layer of flannel in between to help the layers stay put. In addition, the very best option is to use a Walking or Even Feed foot or to engage your machine's built-in fabric feeding system. This allows better control from both the top and the bottom. And, when sewing mixed fabric types, it is traditionally best to sewing with the "trickier" fabric on the bottom against the lower feed dogs as they exert the most control to move the fabric through the machine. Below is a link to our full tutorial on sewing with luxury plush fabrics: 


Ce said:
Ce's picture

No more struggling with mitered corners for me. This is a valuable tutorial. Thank you for providing it!!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Ce - You're welcome. So glad we helped you solve a problem!

Kat L said:
Kat L's picture

Thank you Sew4Home for continually providing fun ways to improve our skills and create beautiful hand crafted items!  I recently purchased a newer machine with a walking foot and a ruffler.  I will be making this blanket soon!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@ Kat L - Thanks for such a nice compliment. We are lucky to have you as a loyal follower. Great news about your new machine!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Janet - Thanks! You're right - there are NEVER enough cute blankies.

VernaL said:
VernaL's picture

I'm a fairly new subscriber and I love your ideas.  The blanket is wonderful, but do you have a pattern for that cute little teddy bear that is tucked inside inside the blanket on one of the photos?  His face is just darling.  I'm becoming a great grandmother in Nov. and would love to make the bear for the new little boy.

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@VernaL - Welcome aboard. We're happy to have you here. That little teddy bear is just a purchased toy - no pattern is on the site. 

VernaL said:
VernaL's picture

Thanks so much for your quick reply.  I will have to look for him when I go shopping.

Lori Mehrer said:
Lori Mehrer's picture

I love that you included the links to the fabric. I use Shannon Minky all the time but I didn't realize that they also produced satin fabrics. I'll have to get some in my next fabric.com order.

daleyg said:
daleyg's picture

Perfect timing -- I need a baby shower gift for next weekend and this would be perfect.  Plus,it'll give me an excuse to figure out how to use the ruffler 

I really appreciate all the great projects you post.  So many of them are "quick and easy" which I really appreciate since I don't have a lot of free time, but they are all very good ideas and definitely "gift" worthy!

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@daleyg - The Ruffler is great - it just looks scary! Thanks for note. We do try very hard to have a good mixture of regular projects along with "quick and easy" ones. Have fun!

Sherrie M said:
Sherrie M's picture

Sew4Home is my one stop shop for anything I might need/want to sew.  I just love this place and I love this little baby blanket.  Great timing too as I need two gifts for new babies this month.  Also thank you so much for making these tutorials so we can download as a pdf that just makes life wonderful for me.  I'll be adding this one to my Sew4Home binder.

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Sherrie - Thanks for the compliments. We so appreciate it - and we love that you are excited about the pattern. Have fun and let us know how yours turn out. 

Ellen M said:
Ellen M's picture

Hi Liz, This is just precious! I don't know which is cuter-- the baby blanket, the elephant Cuddle print, the Silky Satin ruffle, the grey polka dot, the smiling baby, or the grey bear... lol

Please stop killing me with cuteness overload ;)

hugs with Cuddle


Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@Ellen - Thanks! We do often specialize in cuteness - so you'll just have to put up with it