Around these parts, Summer is prime time for outdoor concerts. Seating for these events is usually just the grassy slopes of a natural amphitheater. You gotta bring something to sit on. A blanket is often too big and rather bulky to pack in. Instead, try this lightly padded, roll-up cushion in two great outdoor fabrics. It's filled with foam, which your bottom will like, and the outdoor fabric is weather and water resistant, which your white summer pants will like.

Our thanks to our friends at Fabric.com for providing the great Waverly Sun N Shade fabrics for this project. For more information on choosing outdoor fabrics, take a look at our tutorial on the subject.

Sewing Tools You Need

• Any Sewing Machine (we recommend the Janome DC4030)
• Walking Foot: optional, but helpful to sew through the multiple layers

Fabric and Other Supplies

• 2 yards of 54" wide outdoor fabric in a print: we used Waverly Sun N Shade Sundial Citrine from fabric.com
• 2 yards of 54" wide outdoor fabric in a print: we used Waverly Sun N Shade Stripe Ensemble Citrine from fabric.com
• Coats Outdoor Living Thread in color to match fabrics
• 2 yards of 1" thick x 27" wide Nu-Foam®
  NOTE: Nu-Foam® is mildew resistant and won't yellow or disintegrate so it's great for outdoor use.
• 4 D-rings
• See-through ruler
• Tape measure
• Seam gauge
• Fabric pencil or marking pen
• Scissors or rotary cutter and mat
• Straight pins
• Iron and ironing board

Getting Started

1. Cut a 28" x 72" rectangle from the print fabric. Fussy cut to center the pattern.
2. Cut a 28" by 72" rectangle from the striped fabric. Fussy cut to center the stripes.
3. From the remaining striped fabric, fussy cut THREE strips 3¼" wide x 72" long, centering a stripe on each strip.
   
4. There should be no need to trim the Nu-Foam®; it is already to 27" x 72". It's important it fits tight into the cushion cover to maintain a smooth look. However, if you struggle with the length at all on the very last seam (step #20 below), you can trim off a bit prior to folding in the cover's raw edges and stitching closed.
   

At Your Sewing Machine & Ironing Board

1. Press in ½" along both sides of each strip.
   
2. Fold each strip in half (so they are now 36") wrong sides together, matching the pressed edges.
3. Topstitch close to the edge, starting at the raw end, stitching the length of the strip, pivoting at the fold, stitching across the folded edge, pivoting again, and stitching along the length of the remaining side.
   
4. Each of the three strips will now be a double layer with a finished end and an unfinished end.
5. From one strip, cut a 28" section, starting at the unfinished end. Discard the remainder of the strip. This section will be used as the handle.
6. From each of the remaining two strips, cut a 3" section, again measuring from the unfinished end.
   
7. These 3" sections will hold the D-rings, and the remaining sections with the finished ends are the straps.
8. We used our fabric to plan placement of the handle and straps so the stripe of the straps matched the fabric's stripes. Your fabric may be slightly different; we've also included approximate measurements so you can best match placement on your fabric.
9. Lay your striped 28" x 72" rectangle flat on your work surface, right side up.
10. Position the raw edge of each strap along the vertical stripe closet to each side of the rectangle (or approximately 4" from each side). Pin in place so the raw edge of the strap is flush with the raw end of the rectangle.
11. Insert each end of the handle under each strap at a 90˚ angle 3" up from the raw edge. The handle should insert under the strap almost all the way; leave it just about ¼" short of the opposite folded edge of the strap to conceal the handle's raw edge. The handle will bow in the middle, which allows it to be, well... a handle. Pin the straps and handle securely.
    
    
12. Topstitch the strap in place, following your previous stitch line. Stitch from the raw edge, stopping at the top seam line of the handle, pivot, stitch across the strap, pivot again, and follow the stitch line down the other side to the opposite raw edge.
13. Return to the bottom seam line of the handle and stitch another horizontal line as well as an "X" to reinforce the strap at the point of the handle.
14. Repeat to attach the second strap.
    
15. Slip each 3" section of strap through two D rings and fold in half with the unfinished ends matching. Pin in place over the topstitched raw end of each strap with unfinished ends matching. Machine baste in place.
    
16. Place the 28" x 72" print rectangle over the striped rectangle, right sides together and with all raw sides matching.
17. Stitch together along both sides and the strap end, using a ½" seam allowance. Leave the plain end opposite the straps open. Turn right side out through this open end. 
    NOTE: A waking foot will help keep all your fabric layers from shifting.
18. Push out all the corners so they are nice and sharp and pull out the loops with the D-rings.
    
19. Insert the Nu-Foam®.
    
20. Fold under the open end ½" pin securely, matching the folded edges. Topstitch closed.
    
21. To roll up the mat, start at the end opposite the straps. Roll tightly, smoothing as you go. Secure by inserting the strap through both D rings then back through a single D ring. Cinch to tighten.
22. Grab the handle and head out for Summer Fun.
    

Contributors

Project Design: Alicia Thommas   
Sample Creation, Pattern Design and Instructional Outline: Michele Mishler

Other machines suitable for this project include the Elna 5200 and the Bernina aurora 440QE.

Comments (5)

Liz Johnson, Editor, Sew4Home said:

... @ DT: We got ours at Fabric Depot locally. I checked, but did not see it available at their store online. Fairfield does offer a store locator on their site: http://www.fairfieldworld.com/store-locator/62 It looks like the sell Nu-Foam in most Joann Fabrics stores I also found it online at the Online Fabric Store: http://www.onlinefabricstore.n...Qgod104aoQ

January 18, 2012

DT said:

... This is so cool and I love your tutorials. Can you tell me where you got the Nu-Foam? I found the 27" x 1" in a 10 yard roll, but was hoping not to have to buy such a large quantity. Thanks for what you do!

January 18, 2012

Tsetsgee said:

... Thats great pad. I love your posts

July 23, 2011

Lucy Chin said:

... Megan, you could make it wider by just increasing width or make 2: one for you & your hub and one for the kids. I like the size. I will probably make 2 for my fam. Good to know about using nu-foam and outdoor fabric. I've been thinking about making a fabric cushion using quilt batting for taking out, but worried about it getting damp.

July 22, 2011

Megan Sadler said:

... i wish that was wider so i could include my small (2 babies and a husband) family on my little picknicks

July 22, 2011

Name

Comment

smaller | bigger

Add Comment Preview